What type golf club shaft

The light weight allows golfers to produce greater swing speeds for more power, but sacrifices control due to the flex generated during the swing. Graphite shafts are mainly found in drivers and woods.

Furthermore, they are often suited for female and senior golfers who cannot produce the swing speed to use steel shafts effectively. There are variations in flexes and colours which make graphite shafts a popular choice amongst all golfers. The shafts weigh between grams as compared to steel shafts at around grams. Thanks to the lighter weight, it allows for more distance to be gained. However, getting a consistent feel is difficult compared to a steel shaft.

A downside to graphite shafts is that they require more care. If the paint on the graphite shaft gets worn off, this will negatively affect the performance of the shaft. These are new additions to the shaft market. Multi Material Shafts can be both used on drivers and irons as they combine both steel and graphite into one shaft to try and get the best of both worlds. Typically the tip is graphite whereas the body of the shaft is steel.

Due to the steel section, it allows golfers to control the ball flight more. The graphite tip lets the driver have a limited amount of whip into the ball that can help produce more distance. In addition, the graphite tip helps filter out any unwanted vibrations at contact to optimize the feel of each shot. A relatively new material used to manufacture shafts is titanium.

They are strong and more on the stiff side. Titanium shafts are lighter than steel and have the ability to dampen vibrations. This is good for stronger golfers who have no trouble getting distance on their shots but may be concerned with accuracy. People might question if shaft flex matters, yes very much they do. The right flex for you allows you to get more consistent shots in with better quality of contact with the ball!

There is a lot to learn about shafts. Thanks to innovation and the development of technology, the technology in shafts will constantly advance. Getting the correct weight of your shaft is an important factor to consider as well.

Shafts can range anywhere from 40 to grams. Typically the rule of thumb is that a golfer with a slower swing speed will benefit from using a lighter shaft, and you would add weight as swing speed increases. As you might expect at this point, there are always exceptions. There are players on the PGA Tour using lighter driver shafts with swing speeds upwards of mph. This is another area of getting fit for the right driver that will require a little bit of testing to see what feels most comfortable to the player, and the kinds of results it yields.

One of the biggest misconceptions about shafts is that there are standards out there that manufacturers adhere to. Most golfers assume that a shaft marked regular or stiff will be the same across the board, no matter who they buy it from. Over the past several decades we have seen wildly different performance from what is described by the OEM versus what the customer is actually getting. We often like to compare shafts to hamburgers. Such is the case with shafts.

The quality of the product will affect your ability to strike a golf ball properly. When we put a customer through a fitting, we determine the right profile, weight, and flex that is required.

Frankly, finding the correct shaft for your driver is like navigating a minefield. Golfers buy certain shafts for various reasons. Some want to play the popular shaft on Tour, or the one Tiger Woods uses, or maybe they just heard from a buddy that a certain shaft is awesome. So, in this article, I wanted to help golfers with a few general rules and guidelines for fitting themselves into the right driver shaft.

Hopefully, though, the information here can help you get into the right wheelhouse. Your clubhead speed is a factor in what flex is right for you, but as Briand explains, ball flight and performance are king. A shaft with a 3-degree torque will feel much stiffer than a 5-degree torque, for example. Every shaft — whether it be graphite or steel — has a certain amount of torque. Once the shaft is installed onto your golf club, you must determine the right length for you.

But how important is shaft length, we hear you say? Well, the importance of length, according to research, is extreme. For instance, ball impact that is 0. So, the key to choosing the right shaft is finding the correct length that provides a repeating, solid hit each time. In order to determine the length of your club, stand tall and get someone to measure from the crease where your wrist and hand meet to the floor.

Do this with both hands and take an average of the two measurements. The following lists what length of shafts you should consider for certain heights. If the crease where your wrist and hand meet to the floor is:. If you have picked the wrong shaft, you will immediately know.